Servo Roll Feed
Overview
Complete New Servo Drive and Control Package Including the Following Components:
CHS Automation Rockwell/Allen-Bradley Servo Control Package:
System Overview:
The Allen-Bradley Press Feed Package is a single axis system which is comprised of the following components:
The sizes of the motor and amplifier will vary depending on the actual job requirements
The controls have the following functions as standard:
The basic function is to index a pre-determined length once a feed initiate signal is received. Upon completion of the feed, the feed complete signal is set. This feed drive package has the ability to be controlled via the operator interface, hardwired inputs, or a combination of both.
Description of Software Functions:
Description of Modes:
Manual Mode – In the Manual Mode of operation the following functions can be performed:
Auto Mode – In Auto Mode of operation the following functions can be performed:
Description of Inputs and Outputs:
The following is a description of the input and output functions.
The inputs listed below unless stated otherwise can be controlled by either the hardwired inputs on the input card or they can be controlled by the PanelView Plus terminal. In most cases the inputs can only be controlled be either the hardwired inputs or the PanelView Plus terminal, not both of them.
Hardwired only inputs: These inputs can only be controlled via inputs wired to the input card.
Hardwired or PanelView Plus inputs: The following inputs can be controlled by the hardwired inputs or the PanelView Plus terminal, but not both. The selection of the input source is made on the I/O setup screen on the PanelView Plus terminal.
Hardwired and PanelView Plus inputs: The following inputs can be controlled by both the hardwired inputs and the PanelView Plus terminal at the same time. There is no source setup required for these inputs.
**Note control functions and features may vary from above descriptions depending on the servo drive and controls specific to your needs. Please consult with your sales representative for more information.
The console cabinet is a NEMA 12 enclosure with fusible disconnect.
(2) – 24Volt DC capable dry contacts from the press rotary cam switch will be required. One for automatic feed initiate, and for pilot pin release.
Complete New Servo Drive and Control Package Including the Following Components:
CHS Automation Rockwell/Allen-Bradley Servo Control Package:
System Overview:
The Allen-Bradley Press Feed Package is a single axis system which is comprised of the following components:
The sizes of the motor and amplifier will vary depending on the actual job requirements
The controls have the following functions as standard:
The basic function is to index a pre-determined length once a feed initiate signal is received. Upon completion of the feed, the feed complete signal is set. This feed drive package has the ability to be controlled via the operator interface, hardwired inputs, or a combination of both.
Description of Software Functions:
Description of Modes:
Manual Mode – In the Manual Mode of operation the following functions can be performed:
Auto Mode – In Auto Mode of operation the following functions can be performed:
Description of Inputs and Outputs:
The following is a description of the input and output functions.
The inputs listed below unless stated otherwise can be controlled by either the hardwired inputs on the input card or they can be controlled by the PanelView Plus terminal. In most cases the inputs can only be controlled be either the hardwired inputs or the PanelView Plus terminal, not both of them.
Hardwired only inputs: These inputs can only be controlled via inputs wired to the input card.
Hardwired or PanelView Plus inputs: The following inputs can be controlled by the hardwired inputs or the PanelView Plus terminal, but not both. The selection of the input source is made on the I/O setup screen on the PanelView Plus terminal.
Hardwired and PanelView Plus inputs: The following inputs can be controlled by both the hardwired inputs and the PanelView Plus terminal at the same time. There is no source setup required for these inputs.
**Note control functions and features may vary from above descriptions depending on the servo drive and controls specific to your needs. Please consult with your sales representative for more information.
The console cabinet is a NEMA 12 enclosure with fusible disconnect.
(2) – 24Volt DC capable dry contacts from the press rotary cam switch will be required. One for automatic feed initiate, and for pilot pin release.